CineSticks N1 - WS - ScottyMakesStuff
CineSticks N1 - WS - ScottyMakesStuff



CineSticks N1 - WS

SKU: CS-N1-WS3
Normaler Preis $126.00 Sonderpreis$101.00 Sparen 20%
/

Kartonmenge
  • Schnelle Lieferung
  • Auf Lager
  • Inventar auf dem Weg

Großhandelspackungen von CineSticks N1 von 3 bis 175 Stück.

Kompatibel mit:

DJI RC-N1 (Mini 2, Air 2, Air 2s usw.)    | DJI Smart-Controller    | M300 Enterprise Smart Controller    | Mavic Mini    | Mini SE    | Mavic Air    |    Mavic 2-Serie*  | Evo Nano+   | EvoLite+

Neue aktualisierte Version mit weichen und festen Gummistiefeln, die den ursprünglichen CineStick R2 ersetzt

CineSticks sind resistive Joysticks, die ein spezielles Design verwenden, um Ihnen die reibungslose Steuerung zu ermöglichen, zu der kleine Standard-Joysticks einfach nicht in der Lage sind.

Sie können diese filmischen Bewegungen wie Schwenks, Dollies, Tilts und Trucks ohne diese kleinen Jitter ausführen, die mit Standard-Joysticks so schwer zu vermeiden sind.


Wir verwenden spezielles und superweiches Silikongummi, um Ihnen die reibungslose Bewegung zu ermöglichen, von der Sie geträumt haben. Aber das ist noch nicht alles, wir haben sie mit einstellbarem Widerstand hergestellt, um Sie von einer sanften bis zu einer sehr festen Kontrolle zu bringen, und sie sind so einfach einzustellen!

Die CineSticks gibt es in zwei Längen – Standard und lang. Wenn Sie die langen CineSticks in Betracht ziehen, lesen Sie bitte den Abschnitt „CineStick in welcher Größe?“. unten, um die Verwendungsarten für jeden zu verstehen.

 

Downloads:

CineSticks-Anleitung

CineSticks-Anleitung – Englisch

 

Garantie

12 Monate

 

 

So why do we have these touchy, small joysticks?

When drone flying first started the majority were those homemade FPV drones and when they're raced they needed to be able to turn in microseconds, so it made sense to have such touchy joysticks.

Unfortunately, it seems that nobody at the drone manufacturers ever considered the kind of joysticks that would suit standard consumer drones (cinema drones) so we got lumped with these unsuitable sticks.

 

Not only are our CineSticks good for cinematic motion, but due to the very deliberate and smooth motion, we've found that newcomers to droning find they can get the hang of things far quicker.

These are made for standard consumer drones (cinema drones) and are not really suitable for FPV drones. It uses the standard 4mm screw to attach.


How to use

See 'Other Controllers' for Cup Style Mounts

To attach the CineSticks, first, make sure that the bolt is fully unscrewed with the 4mm bolt protruding - Just pinch the neck of the silicone rubber and unscrew (counter-clockwise) the stick until you get to the end stop. Then pinch the rubber neck and screw (clockwise) into the joystick threaded hole until it stops turning. At this point just continue screw it (clockwise) until you get to your desired resistance.

To increase the firmness/resistance, you just screw down the joystick. To soften/decrease the resistance, pinch the neck of the silicone rubber and unscrew the stick. You will need to pull the rubber up so there's no gap between the rubber cap and the stick.

To Remove the CineSticks, just pinch the neck of the silicone rubber and unscrew the rubber a few times to remove it.

Note: When using the CineSticks, particularly at high resistance, letting go of the joysticks may not return to the centre exactly. Instead, you should bring the CineSticks back to the centre and then confirm visually that there is no drift. For controllers that perform a pre-flight stick check, it’s best to start up with the CineSticks at low resistance before increasing resistance. It’s recommended that you store the CineSticks with the resistance off to keep your CineSticks performing at their best.

How to tell which mount style you have?

The CineSticks to Cup Mount Adapter (supplied with all CineSticks as a pair for 27th July) takes the CineSticks (based on the current DJI 4mm screw in bolt joystick mounts) and connects them to the previous cup style mounts that have an internal M6x0.75mm thread such as Mavic 2 series and Mini 1.

Compatibility:

The CineSticks attach into the 4mm threaded hole, the same way that many detachable joysticks do.

There are undoubtedly more compatible controllers than the following list. These are just the controllers we've tested so far.

Compatible with;

DJI's standard light grey coloured RC-N1 controller that comes with the Mavic 3 Standard, Mini 2, Mavic Air 2, Air 2S. Also the DJI Smart Controller (current model CP.MA.00000080.01), M300 Enterprise Smart Controller.

Compatible with use of the supplied Cup Mount Adapter; 

Mavic Mini 1, Mini SE, Mavic Air, Mavic 2 Pro with Smart Controller (this controller has come with both attachment types so check your sticks to be sure) ,Mavic 2 Series 

    For all other controllers, please refer to the info above to see if the controller you have has the unscrewable joysticks as described.


    Current DJI M4 screw type joystick - Cinesticks directly replace this type of Joystick Previous DJI Cup style internal M6x0.75 Thread that requires the cup mount adapter to work with the CineSticks - as above
     

    How to use

    To attach the Cup Mount Adapter, first remove the current cup style joysticks. Take the end of the cup mount adapter with the larger opening, and screw it down with your fingers until it's firmly on. Then attach the CineStick directly to the top of the adaptor.

     


    Zuletzt Angesehen